 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| file name:elgt-150-c-spec 2017-07-10 elgt-150-c series ! " # ! # " " # #!$!% #$ # &' # # " ! ( ) *% " + # " " " , !$ # -./0 " " 0 " ( # #$ # * 1- $ ! ! # # % " # "#! 234) 234 $ # # # " # (#" ## #!## $$ # % 5! $$ " #! ! # #$ # 0 ! " "## # 0 # # $ # " #$ 6 ( , # " , % 7 "#! " ! # #! # ! # #!$! 8! 39 ! # :% ;# # (, $# # !$ # 234) 234 # ## # #!## # 9! # #$ # < #!$! =! ( $# # > & ? ## @> > 2> ,$ a "#! , , " " (# " (, " "#! " ## " #$ , " $$ # 9! # #$ # ,$ 8 + a 8 23 234) 234 234) 2# 6% 2# =! ( " #!" (! $# # % & ! # ?' 0 ' 37 @ 9! # ;# 2 # + 2 # + 2 # + ip67 ip65 ? # ,$ # ,@ #!$! ! ?) *@ 234) 2 # # " # #,% 2 # + . 234) 8! $ # ( ! # % 2 # + 105~150w class constant current mode led driver 105~150w class constant current mode led driver elgt-150-c series specification model rated current rated power output current adj. range set up time note.4 voltage range note.3 frequency range power factor (typ.) efficiency (typ.) ac current (typ.) input inrush current (typ.) leakage current safety standards emc immunity working temp. working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing over temperature over voltage 1600ms/115vac 500ms/230vac (please refer to "static characteristic" section) 47 ~ 63hz <0.7ma / 240vac compliance to en55015,en61000-3-2 class c (@load 60%) ; en61000-3-3 R ; gb/t17743, gb17625.1 20 ~ 95% rh non-condensing -40 ~ +80 , 10 ~ 95% rh 0.03%/ (0 ~ 60 ) 10 ~ 500hz, 5g 12min./1cycle, period for 72min. each along x, y, z axes environment safety & emc protection shut down o/p voltage, re-power on to recover shut down o/p voltage, re-power on to recover short circuit hiccup mode, recovers automatically after fault condition is removed i/p-o/p:3.75kvac i/p-case:3.75kvac o/p-case:1.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh withstand voltage isolation resistance file name:elgt-150-c-spec 2017-07-10 current tolerance 5.0% constant current region note.2 total harmonic distortion open circuit voltage (max.) adjustable for a-type only (via built-in potentiometer) cold start 65a(twidth= s measured at 50% ipeak)/230vac 485 per nema 410 ; max. no. of psus on 16a circuit breaker 3 units (circuit breaker of type b) / 6 units (circuit breaker of type c) at 230vac tcase=-40 ~ +90 (please refer to ? output load vs temperature? section) max. case temp. tcase=+90 compliance to en61000-4-2,3,4,5,6,8,11; en61547, light industry level ( ) surge immunity line-earth 6kv, line-line 4kv enec en61347-1, en61347-2-13 independent, en62384; gb19510.1, gb19510.14; % $ ;b $ , # ! .&' $!0 . # ( $ ! % ! .% 3 # c2'2; 7db b9 7bec% 9# ,$0 # ! # 4// # 6 ! # ! $# ,% &% , ( ! # $! # % 3 % # f 2 d2 2g # # *% " # !$ ! # % ! b; b99 " , # # " !$ % % " # #$# " ( #$ #( # " 5! $ % 7 $ # ( (, " #$ # 0 " 5! $ ! ! ! 5! , 7 # " #$ # % 4% " " ,$ 6$ , # a0 "#! # #$ # " 0 $ ! , $# ?# 730 $ @0 (#! ) # % )% 3 # " , # 7; h ( "$< % % # current ripple 5.0% max. @rated current 100 ~ 305vac 142 ~ 431vdc 72 ~ 143v 1050ma 151v 525 ~ 1050ma 92% 92% 91% 1.7a / 115vac 0.9a / 230vac 0.7a/277vac 230 ~ 265v 155 ~ 180v 128 ~ 150v 2 *63*3 19 5.5 mm (l*w*h) 0.95kg; 16pcs / 16.0kg / 0.77cuft ip65 or ip67 approved pf 0.97/115vac, pf 0.95/230vac, pf 0.92/277vac@full load RRR (please refer to "power factor (pf) characteristic" section) thd< 20%(@load 50%/115vc; @load 60%/230vac; @load 75%/277vac) RR R (please refer to ?total harmonic distortion(thd)? section) no load power consumption <0.5w for blank / a / d2-type no load / standby power consumption standby power consumption <0.5w for b / da-type 1098.95k hrs min. telcordia sr-332 (bellcore) 308.5khrs min. mil-hdbk-217f (25 ) 105w 200vac ~ 305vac 100vac ~ 180vac 150.15w elgt-150-c1050 elgt-150-c700 700ma 149.8w 105w 107 ~ 214v 225v 350 ~ 700ma elgt-150-c1400 54 ~ 107v 1400ma 115v 700 ~ 1400ma 105w 149.8w dali standards compliance to iec62386-101, 102, 207 for da-type only emc emission file name:elgt-150-c-spec 2017-07-10 elgt-150-c series block diagram detection pwm & pfc circuit o.l.p. o.t.p. emi filter rectifiers power switching filter & rectifiers vo+ vo- i/p control o.v.p. & o.l.p. pfc circuit pfc fosc : 50~120khz pwm fosc : 60~130khz dim+ (b type) dim- driving methods of led module this series works in constant current mode to directly drive the leds. typical output current normalized by rated current (%) in the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. should there be any compatibility issues, please contact mean well. 100 50 (min.) vo(%) 50 100 io(%) constant current area hiccup protection this characteristic applies to blank/a/b/d2-type, for da-type, the constant current area is 60%~100% vo. case :functional ground 105~150w class constant current mode led driver ac/l(brown) ac/n(blue) file name:elgt-150-c-spec 2017-07-10 elgt-150-c series dimming operation elgt-150-c 3 in 1 dimming function (for b-type) output constant current level can be adjusted by applying one of the three methodologies between dim+ and dim-: 0 ~ 10vdc, or 10v pwm signal or resistance. direct connecting to leds is suggested. it is not suitable to be used with additional drivers. dimming source current from power supply: 100 a (typ.) applying additive 0 ~ 10vdc applying additive 10v pwm signal (frequency range 100hz ~ 3khz): applying additive resistance: note : 1. min. dimming level is about 8% and the output current is not defined when 0%< out<8%. i 2. the output current could drop down to 0% when dimming input is about 0k or 0vdc, or 10v pwm signal with 0% duty cycle. vo+ vo- dim+ dim- + + + - - - do not connect "dim- to vo-" additive voltage vo+ vo- dim+ dim- + + - - do not connect "dim- to vo-" additive pwm signal vo+ vo- dim+ dim- + + - - do not connect "dim- to vo-" additive resistance 0v 1v 2v 3v 4v 5v 6v 7v 8v 9v 10v 10% 0% 20% 30% 40% 50% 60% 70% 80% 90% 100% output current (%) 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 10% 0% 20% 30% 40% 50% 60% 70% 80% 90% 100% output current (%) 10% 0% 20% 30% 40% 50% 60% 70% 80% 90% 100% output current (%) dimming input: additive voltage duty cycle of additive 10v pwm signal dimming input * dim+ for b-type da+ for da-type prog+ for d2-type * *dim- for b-type da- for da-type prog- for d2-type short 10k/n 20k/n 30k/n 40k/n 50k/n 60k/n 70k/n 80k/n 90k/n 100k/n (n=driver quantity for synchronized ) dimming operation dimming input: additive resistance dim-(black)** dim+( )* gray vo+(brown) vo-(blue) 105~150w class constant current mode led driver file name:elgt-150-c-spec 2017-07-10 elgt-150-c series dal interface (primary side; for da-type) i apply dali signal between da+ and da- . dal protocol comprises 16 groups and 64 addresses. i first step is fixed at 8% of output. smart timer dimming function (for d2-type by user definition) mean well smart timer dimming primarily provides the adaptive proportion dimming profile for the output constant current level t o perform up to 14 consecutive hours. 3 dimming profiles hereunder are defined accounting for the most frequently seen applications. if other opti ons may be needed, please contact mean well for details. ex : d01-type: the profile recommended for residential lighting ex: d02-type: the profile recommended for street lighting **: time matches operating time in the diagram whereas level matches dimming level. example: if a residential lighting application adopts d01-type, when turning on the power supply at 6:00pm, for instance: [1] the power supply will switch to the constant current level at 100% starting from 6:00pm. [2] the power supply will switch to the constant current level at 70% in turn, starting from 0:00am, which is 06:00 after the po wer supply turns on. [3] the power supply will switch to the constant current level at 50% in turn, starting from 1:00am, which is 07:00 after the po wer supply turns on. [4] the power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the po wer supply turns on. the constant current level remains till 8:00am, which is 14:00 after the power supply turns on. **: time matches operating time in the diagram whereas level matches dimming level. example: if a street lighting application adopts d02-type, when turning on the power supply at 5:00pm, for instance: [1] the power supply will switch to the constant current level at 50% starting from 5:00pm. [2] the power supply will switch to the constant current level at 80% in turn, starting from 6:00pm, which is 01:00 after the po wer supply turns on. [3] the power supply will switch to the constant current level at 100% in turn, starting from 8:00pm, which is 03:00 after the p ower supply turns on. [4] the power supply will switch to the constant current level at 60% in turn, starting from 1:00am, which is 08:00 after the po wer supply turns on. [5] the power supply will switch to the constant current level at 80% in turn, starting from 4:00am, which is 11:00 after the po wer supply turns on. the constant current level remains till 6:30am, which is 14:00 after the power supply turns on. set up for d01-type in smart timer dimming software program: set up for d02-type in smart timer dimming software program: time** time** 06:00 01:00 t1 t1 t2 t2 t3 t3 t4 t4 t5 07:00 03:00 11:00 8:00 11:00 --- --- level** level** 100% 70% 80% 50% 50% 100% 70% 60% 80% dimming level(%) operating time(hh:mm) dimming level(%) operating time(hh:mm) 105~150w class constant current mode led driver file name:elgt-150-c-spec 2017-07-10 elgt-150-c series ex: d03-type: the profile recommended for tunnel lighting set up for d03-type in smart timer dimming software program: time** 01:30 t1 t2 t3 11:00 --- level** 70% 100% 70% **: time matches operating time in the diagram whereas level matches dimming level. example: if a tunnel lighting application adopts d03-type, when turning on the power supply at 4:30pm, for instance: [1] the power supply will switch to the constant current level at 70% starting from 4:30pm. [2] the power supply will switch to the constant current level at 100% in turn, starting from 6:00pm, which is 01:30 after the p ower supply turns on. [3] the power supply will switch to the constant current level at 70% in turn, starting from 5:00am, which is 11:00 after the po wer supply turns on. the constant current level remains till 6:30am, which is 14:00 after the power supply turns on. dimming level(%) operating time(hh:mm) 105~150w class constant current mode led driver -25 80 82 84 86 88 90 92 94 50% 60% 70% 80% 90% 100% 277v(150w) 230v(150w) 115v(120w) load file name:elgt-150-c-spec 2017-07-10 elgt-150-c series pf load output load vs temperature total harmonic distortion (thd) ambient temperature,ta ( ) load (%) input voltage (v) 60hz load (%) (horizontal) power factor (pf) characteristic tcase ( ) load (%) (horizontal) de-rating is needed under low input voltage. efficiency vs load elgt-150-c series possess superior working efficiency that up to 92% can be reached in field applications. -40-250 204555657590 20 40 60 80 100 700ma model, tcase at 75 700ma model, tcase at 75 efficiency(%) thd load tcase at 75 230vac input only -40 -25 0 -10 15 30 50 60 70 20 40 60 80 100 100 120 140 160 180 200 240 250 260 270 280 305 100 90 80 70 60 50 40 static characteristic 0.88 0.9 0.92 0.94 0.96 0.98 1 50% 60% 70% 80% 90% 100% 277v(150w) 230v(150w) 115v(120w) (105w) (150w) (150w) (105w) (150w) (150w) 230vac input only 4% 6% 8% 10% 12% 14% 16% 18% 50% 60% 70% 80% 90% 100% 277vac(150w) 230vac(150w) 115vac(120w) 105~150w class constant current mode led driver life time tcase ( ) lifetime(kh) elgt-150-c series file name:elgt-150-c-spec 2017-07-10 0 20 40 60 80 100 120 20 30 40 50 60 70 80 90 105~150w class constant current mode led driver file name:elgt-150-c-spec 2017-07-10 mechanical specification elgt-150-c series case no.: 237a unit:mm tc : max. case temperature tc 208 219 195 300 20 300 20 45.8 63 35.5 35 ac/l(brown) ac/n(blue) 105 20 vo+(brown) vo-(blue) sjow 17awgx2c &h05rn-f 1.0mm 2 sjow 17awgx2c &h05rn-f 1.0mm 2 208 219 195 300 20 300 20 45.8 63 35.5 35 ac/l(brown) ac/n(blue) 105 20 b da/d2-type / tc : max. case temperature tc * dim+ for b-type da+ for da-type prog+ for d2-type * *dim- for b-type da- for da-type prog- for d2-type dim-(black)** dim+( )* gray vo+(brown) vo-(blue) sjow 17awgx2c &h05rn-f 1.0mm 2 sjow 17awgx2c &h05rn-f 1.0mm 2 sjow 17awgx2c &h05rn-f 1.0mm 2 blank-type 4- 4.5 4- 4.5 105~150w class constant current mode led driver a-type tc : max. case temperature tc 208 219 195 300 20 300 20 45.8 63 35.5 35 ac/l(brown) ac/n(blue) 50.5 16.5 105 20 sjow 17awgx2c &h05rn-f 1.0mm 2 sjow 17awgx2c &h05rn-f 1.0mm 2 vo+(brown) vo-(blue) please refer to : http://www.meanwell.com/manual.html manualinstallation file name:elgt-150-c-spec 2017-07-10 elgt-150-c series 4- 4.5 105~150w class constant current mode led driver |
Price & Availability of ELGT-150-C700A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |